Consumer Electronics

To prevent dangers, install a tilt switch on heaters to detect if the device is tilted by the change of high/low signal sent by the tilt switch. Auto shut off switch application could be applied to fans, dehumidifiers, humidifiers, air purifier etc. Angles option of tilt switch: 15°, 20°, 30°, 45°, 65° #Tilt Switch #Tip Over Switch #Auto Shut Off Switch #Roll Ball Switch

Recommend Model
OncQue RBS311110 Photoelectric 45° Tilt Switch
Operating Angle: 45° Type: DIP Suitable for Vertical PCB Dimension: 8*10.5*10 mm


OncQue RBS310910T SMD Photoelectric 45° Tip Over Switch
Operating Angle: 45° Type: SMD Suitable for Vertical PCB Dimension: 8*10.5*10 mm


OncQue RBS330313 Photoelectric 15° Tilt Switch
Operating Angle: 15° Type: DIP Suitable for Horizontal PCB Dimension: 10.5*8*12 mm

To avoid UVC light shining into the eyes, install a tilt angle switch on UVC light to detect if the light is tilted up by the change of on/off signal sent by the tilt angle switch. Angles rangeof tilt switch: 45° to 135°
Recommend Model OncQue RBS070310 135° Tilt Switch For Reverse Mount PCB
Operating Angle: 135° Type: DIP Suitable for reverse mountPCB Dimension: 8*10.5*10 mm


OncQue RBS200100 4 Direction 45° TiltSwitch
Operating Angle: 45° Type: SMD Suitable for Vertical PCB Dimension: 8*10.5*10 mm


OncQue RBS360104 Photoelectric 65° Tilt Switch
Operating Angle: 65° Type: DIP Suitable for Horizontal PCB Dimension: 10.5*8*12 mm

Auto Shut-off
Install a shock sensor on irons, shock sensor provides ON/OFF signal continuously when user keep using irons, irons will keep working at this situation; once the signal maintains at ON or OFF signal for a certain time, irons will be automatic power-off by program design in order to prevent dangers.


3-way Auto Shut-off
Install a three-way tilt sensor on irons, when irons left-leaning, right-leaning or in upright status, irons will be automatic power-off after a while due to High/Low signals change in order to prevent danger.

Recommend Model
OncQue RBS020902T SMDShock Sensor
Switch State: SMD Normal Open Suitable for Horizontal PCB Dimension: Ø3*7.8 mm

When remote controls are not in use, the tilt sensor inside remote control keeps at OFF signal, remote controls are in sleep mode. When users pick up the remote controls, tilt sensor provides ON signal and remote controls will be turned on automatically. The batteries will last longer by install tilt sensor on remote controls.
Recommend Model
OncQue RBS020902 SMD Tilt Angle Detecting Sensor Switch
Operating Angle: <20° Switch State: SMD Normal Open Suitable for Horizontal PCB Dimension: Ø3*7.8 mm


OncQue RBS200112 20°Tilt Detecting For 4 Directions Sensor Switch
Operating Angle: 20° Switch State: DIP Normal Open Suitable for Horizontal PCB Dimension: 9.58*4.5*4.5mm


OncQue VBS030600 SMD Sensitive Omni-Directional Vibration Sensor Switch
Type: SMD Both Suitable for Horizontal and Vertical PCB Dimension: 4*4*7.5 mm Not sold in the USA

Install a tilt sensor switch on a filter cartridge module to count the number of using times by the change of ON/OFF signal when pouring water. Through this, filter cartridges will be used more reasonably and effectively by counting number of using times rather than time countdown.
Recommend Model
OncQue RBS020902 SMD Tilt Angle detecting Sensor Switch
Operating Angle: <20° Switch State: SMD Normal Open Suitable for Horizontal PCB Dimension: Ø3*7.8 mm

Install a tilt sensor switch on sweeping robots, when sweeping robots tilted or flip over, the tilt sensor will change ON/OFF signal and make sweeping robots shut-off automatically in case of danger.
Angles option of tilt sensor: 15°, 20°, 30°, 45°, 65°
Recommend Model
OncQue RBS330211T SMD Photoelectric 30° Tilt Angle Sensor Switch
Operating Angle: 30° Type: SMD Suitable for Horizontal PCB Dimension: 8*10.5*12 mm


OncQue RBS360101 Photoelectric 30° Tilt Angle Sensor Switch
Operating Angle: 30° Type: DIP Suitable for Horizontal PCB Dimension: 8*10.5*10 mm

When users open the material box of sewing machines to supplement or change materials, tilt sensors will change ON/OFF signal because the cover of the material box is opened and make sewing machines stop working to prevent users from injury.
Angles option of tilt sensor: 15°, 20°, 30°, 45°, 65°
Recommend Model

OncQue RBS020902 SMD Tilt Angle detecting Sensor Switch
Operating Angle: <20° Switch State: SMD Normal Open Suitable for Horizontal PCB Dimension: Ø3*7.8 mm


OncQue RBS200112 20°Tilt detecting for 4 directions Sensor Switch
Operating Angle: 20° Switch State: DIP Normal Open Suitable for Horizontal PCB Dimension: 9.58*4.5*4.5mm


OncQue RBS151100One Axis 15° Tilt detecting Sensor Switch
One Axis 15° tilt detecting in Horizontal position installed above or under PCB Switch State: DIP Normal Open Dimension: 5*6*7 mm

Install a vibration sensor module to detect earthquake detecting.It can provide different vibration levels sending different signal. The detection level can be adjusted according to requirements.(Magnitude 3 or Magnitude 4)

Recommend Model
OncQue VSM010100 Earthquake Sensor Module
Different vibration levels sending different signals